Calibrate Incubator Thermometer and Hygrometer: Simple Salt Test Guide
A half-degree error on an incubator thermometer can be the difference between a great hatch and a disappointing one. Many low-cost digital thermometers and hygrometers are off out of the box, and the display often looks perfectly confident while being wrong.
The good news is that you can calibrate incubator thermometer and hygrometer sensors at home in a day, with items you already own. Here is how.
Why Incubator Accuracy Matters
Chicken eggs are set at about 99.5°F (37.5°C) in a forced-air incubator. Running even 1°F too high for several days can cause early deaths and deformed chicks, while running too cool slows development and leads to weak, late hatchers. Humidity errors cause similar problems: too dry and chicks stick in the shell, too wet and they can drown or hatch oversized and soft.
Before you blame your eggs, check your instruments. If you are troubleshooting poor hatches, our list of common incubation mistakes is a great companion to this guide.
What You Need
- Your incubator thermometer and hygrometer (or a combined digital unit)
- A trusted reference thermometer, such as a digital medical thermometer
- Table salt and a small bottle cap
- A zip-top bag or small sealed container
- A pen and notepad to record offsets
Step 1: Check the Thermometer
- Turn the incubator on and let it stabilize for at least 24 hours with no eggs inside.
- Place your thermometer at egg height, not on the floor or hanging near the heater. The reading should reflect the temperature the eggs actually feel.
- Place the reference thermometer right next to it and wait 30 minutes.
- Compare the readings. If your thermometer says 99.5°F and the reference says 98.9°F, your thermometer reads 0.6°F high. Write this offset down.
- Adjust your controller accordingly, or simply remember the offset when setting your target. If your controller allows a calibration setting, use it. Our guide to setting up a temperature controller shows how.
Tip: You can also check the low end with an ice-water bath. A good thermometer should read close to 32°F (0°C) in a slush of crushed ice and water. If it is far off there, it probably is not reliable at incubation temperature either.
Step 2: Calibrate the Hygrometer with the Salt Test
The salt test is the standard way to check a hygrometer. Salt in a sealed space creates an environment of about 75% relative humidity, which gives you a known reference point.
- Pour a small amount of table salt into the bottle cap.
- Add a few drops of water, just enough to make a damp, slushy paste. It should not be dissolved into a liquid.
- Place the cap and the hygrometer together inside the zip-top bag, making sure the sensor does not touch the salt. Seal the bag.
- Leave it at room temperature, away from sunlight, for 8 to 12 hours.
- Read the hygrometer. It should show about 75%. If it shows 70%, it reads 5% low, so add 5 when interpreting its numbers. If it shows 80%, it reads 5% high.
How to Use Your Offsets
Write the offsets on a piece of tape and stick it to the incubator. For example: “Thermometer reads +0.6°F, hygrometer reads -5%.” Now you can adjust settings with confidence and keep consistent records from hatch to hatch.
When to Replace Instead of Calibrate
If a sensor is off by more than a few degrees or percentage points, jumps around, or gives different readings each time you test it, replace it. Accurate sensors are inexpensive compared with a lost hatch. Browse our sensors and controllers for reliable replacements, and see our guide to incubator spare parts if you suspect a heater or fan problem.
Frequently Asked Questions
How often should I calibrate my incubator?
Check before every hatch season and any time hatch rates drop unexpectedly. Hygrometers tend to drift over time, so a quick salt test every few months is a good habit.
Can I trust the built-in display on my incubator?
Treat it as a starting point. Always cross-check it with at least one independent thermometer and hygrometer.
Want hatch-ready gear? Explore our tabletop incubators and cabinet incubators for dependable temperature control.
Your flock starts
the morning with you.
So should your coffee. Meet the coffee made for chicken keepers.
DISCOVER THE COFFEE ↗